Drop 1 5 2 3

While you are here please view our specials on all kinds of backup power related products such as..
* manual transfer switches
* automatic standby generators
* automatic transfer switches
* metering & instrumentation
* UPS systems
Tired of paying those rising electricity rates? We also sell alternative energy products including..
* micro hydroelectric systems
* wind power systems
* solar
Are YOU ready for the next power outage?

Use this calculator to estimate cable voltage drop forsizing conductors. The calculation assumes uncoated copper or aluminum conductorsoperating at the temperature selected and is based on the ac/dcresistance or impedance from NEC 2011 Chapter 9, Tables 8 and 9 for stranded conductorsoperating on a DC or AC 60Hz system. Rather than using the 'k' factor orthe 'Effective Z' of Table 9 this method is based on the actual ac resistanceand reactance values from the table. The load current input is fixed, as is thebase system Voltage. The Voltage drop in the cable is calculated using Ohm's Lawwhere V_drop = I_loadx R_cable. The percent drop is V_drop/ V_system x 100. For ac systems the acimpedance is used in place of the dc R_cable.This methodology is similar to the examples given after NEC Table 9.

Theampacity of each conductor size shown for reference in the dropdown menu below is based on NEC2011Table 310.15(B)(16) for 60C insulated conductors rated 0 through 2000 volts with not morethan three current carrying conductors in raceway, cable or earth with anambient of 30°C (86°F). Exif editor 1 1 14.

Note that the actual ampacity and voltage drop for yourapplication may differ from these results but in most cases will be very close tothose shown here.

Units herein are American Wire Gauge (AWG) and English (feet).

Note, to run this calculator JavaScripts must be enabledon your browser.

Click here for alternate calculator that also includes a transformer and motor load.

NOTES:

1. Examples for parallel runs: 120/240V single phase system with single black-red-white conductors (installed in single conduit) select 'single set of conductors', 120/208V 3phase system with 2 conductors per phase and neutral (installed in 2 parallel conduits) select '2 conductors per phase in parallel', dc system with 3 positive and 3 negative conductors select '3 conductors per phase in parallel'.

2. Voltage drop for ac systems should total no more than 5% under full load conditions. This is recommended by the NEC 210.19(A)(1) Informational Note No. 4 which states a 3% limit for branch circuits and NEC 215.2(A)(4) Informational Note No. 2 which states a 3% limit for feeders. Both of these set a limit of 5% total for both. Drop may be significantly larger during surge or motor starting conditions -- sometimes in the 15% to 25% range if other devices on the system can withstand this momentary dip. Voltage drop for dc systems should be designed as low as possible or less than 2%.

3. For most 120/240V systems using cables of adequate ampacity, voltage drop is not a concern unless cable lengths are well over a hundred feet. A common rule of thumb is to check the voltage drop when the one-way circuit length in feet exceeds the system voltage number. Therefore, using this rule one would check the drop for a 240V system if the circuit length exceeds 240 feet.

4. For refining the calculation the conductor operating temperature can be estimated as follows: If the operating current equals the ampacity listed in NEC Tables 310.15 then the temperature can equal the rating of the table column. If the operating current is less than the ampacity listed then the temperature will be less. Since conductor heating is equal to the I² x R losses, and the heating is proportional to the conductor temperature rise, then the operating temperature will be approximately (I_operating / I_ampacity)² x (T_rating - 30°C) + 30°C. For example, a 50 Amp load using 75°C rated copper conductor requires #8 AWG per Table 310.15(B)(16). If the wire size is increased to #6 AWG for voltage drop considerations then the conductor operating temperature would be (50A / 65A)² x (75°C - 30°C) + 30°C = 57°C. This results in a slight reduction of the voltage drop and may be useful for marginal calculations.

5. All references to the NEC refer to National Fire Protection Association, NFPA 70^®, National Electrical Code^®. or National Electrical Code^® Handbook.

Nch software express burn plus 5 14 full crack. More information about voltage drop based on IEC standards is available in the Schneider Electric Electrical Installation Guide.